Sunking PCB

SMD Stencil Aperture Shapes by Component Type | Sunking Circuits

Design Guide2026-10-20Sunking Circuits Technical Team
SMD Stencil Aperture Shapes by Component Type | Sunking Circuits

The job of an aperture shape is not to copy the pad. It is to tip a tug-of-war — paste sticking to the aperture wall versus paste sticking to the pad — in favour of the pad. That contest exists for every component, but it fails in a different direction for each. Lose it on a small chip part and you get bridging or tombstoning. Lose it on a QFN thermal pad and you get either a slug that will not release or a void-riddled joint. Lose it on a BGA and the problem usually is not release at all, it is position. And for through-hole reflow, release was never the question — volume was. One stencil cannot run a single aperture logic across all of them.

1. Aperture geometry governs release, not appearance

After the squeegee passes, paste sits in the aperture. The stencil lifts. In that instant, two adhesion forces pull on the same paste brick: the wall holds it up, the pad pulls it down. Which side wins depends on the ratio between those two contact areas and their condition.

That is why aperture geometry changes release behaviour and not just deposited volume:

  • The perimeter sets how much paste touches the wall.
  • The area sets how much paste touches the pad.
  • The ratio between them, not either number alone, drives release tendency. Two apertures with identical printed area — one a narrow slot, one square — do not release the same way.

How that ratio is quantified and where the thresholds sit is a separate subject, and we covered it in the area ratio and aspect ratio criteria article. This article does not restate those criteria. It covers which direction each component family pushes that ratio, and what to do about it.

One prerequisite that gets skipped: aperture shape only works if the wall itself is sound. Rough walls, burrs, worn coating — no geometry fixes that. Wall condition and coatings are an independent variable line. This article assumes the stencil body is acceptable.

2. Small chip parts: bridging and tombstoning push the shape inward

Two-terminal passives bring a very specific cluster of print problems.

Bridging first. The gap between the two pads is narrow. Paste only has to slump slightly past the pad edge for the two sides to find each other during reflow. So the common treatment is to pull the aperture in, not match the pad. And the reduction is usually not symmetric — more on the side facing the component centre, less on the outboard side, because the risk is concentrated in that middle gap.

Tombstoning second. If the two ends receive unequal paste, one end wets first during reflow, lifts the part, and the other end has not melted yet. The root cause usually is not the stencil — it is thermal asymmetry between the two pads, one tied to a copper plane and the other to a thin trace. What the stencil side *can* do is keep the two aperture areas equal, rather than sizing one up just because there was room for it.

Third, bridging under the component body. When two apertures sit too close, paste collects beneath the part and can form a connection after reflow that neither optical inspection nor electrical test reliably catches. So the reduction on these apertures is not only a print measure, it buys reflow margin.

Takeaway: chip-part apertures are subtractive. The difference from the pad is deliberate and directional — which is exactly why an aperture file cannot be exported straight from the pad layer.

3. QFNs and large thermal pads: why one big opening gets broken up

QFN, DFN and anything with a large thermal pad has the opposite problem to chip parts. The pad is big, so release is not the hard part. Two other things are.

First, too much paste floats the part. Open a large thermal pad one-to-one and the deposited volume is substantial. During reflow that mass melts and lifts the body slightly, and the fine perimeter leads around it can end up with poor contact or open joints. So large pads are normally broken into multiple smaller apertures with a combined area less than the pad.

Second, gas needs a way out. A single continuous paste mass traps flux volatiles in the middle, producing voids. Once the opening is subdivided, the gaps between segments act as escape paths in the early stage of melting.

Common subdivision approaches, each with a different emphasis:

  • Uniform segmentation — an array of equal small apertures. Most common; escape paths distribute evenly.
  • Webbed grid — webs left across one large opening. We wrote about this approach separately; the point is that webs must block paste without being so narrow they deform themselves.
  • Denser centre, sparser edge — used when the thermal path has direction, but this one must be confirmed with the design side, never decided unilaterally by the stencil shop.

Third, the fine perimeter leads and the central thermal pad often want different deposit thicknesses. At that point shape is no longer the right lever and thickness is — meaning step stencils and similar structural measures. There is an order to respect here: try shape first, thickness only when shape cannot do it, and pad redesign only when thickness cannot either. Reversing that order turns a local problem into a board-wide one.

4. BGAs: round apertures, and why shape error eats registration margin

BGA pads are round and the apertures are normally round too. Not much to debate there. What matters is a different point: in a BGA field, shape error and position error act together.

BGA pitch is tight and the pad field is highly regular. If the stencil sits slightly offset relative to the board, every aperture is offset in the same direction. Add an oversized aperture to that offset, and paste crosses the solder mask boundary into adjacent territory.

Two working conventions follow:

  1. Apertures no larger than the pad, usually slightly smaller. In a BGA field, extra area is not margin, it is exposure.
  2. Keep the shape a clean circle. Do not switch to a square or rounded square to recover area. Four corners are four stress concentrations at release, and the printed result drifts from what the geometry predicted.

One more thing that shows up disproportionately in BGA fields: this area is the most sensitive to board flatness. Dense pads and small apertures mean that any local non-contact lets the squeegee smear paste under the stencil. Board support and tooling flatness is an independent print-side variable and no aperture shape compensates for it. Recurring smear in a BGA field means check the support first, not the geometry.

And once apertures approach their physical floor, there is no shape headroom left to trade. What sets that lower bound is covered in the microelectronics printing article; in that regime the decision is a different stencil fabrication route, not further geometry tuning.

5. Connectors and paste-in-hole: volume, not fit

When through-hole parts are reflowed (paste-in-hole / through-hole reflow), the printing logic inverts.

For every family above, the aperture exists to leave a layer of paste on a flat surface. Paste-in-hole has to push paste into a hole and deliver enough of it that, once molten, the barrel fills and forms an acceptable joint. The hole has volume, and paste shrinks as flux volatiles leave. Therefore:

  • Apertures must be clearly larger than the pad, extended outward, with that extra area covering the volume shortfall. This is the exact opposite direction to chip parts.
  • The shape is usually not round but extends into wings or rectangular lobes outboard of the pad. The extension direction has to avoid neighbouring pads and apertures.
  • The hole itself counts as part of the opening, so these apertures cannot be designed without hole size, board thickness and annular ring in view — and those are PCB-side parameters, not stencil-side decisions.

Surface-mount connectors are a third case again. The leads are often fine, yet the body is heavy and placement accuracy matters. Points to watch:

  • Lead apertures guard against bridging, logic close to chip parts: pull in.
  • Hold-down or ground tabs tied to copper planes sit in a different thermal environment from signal leads, so their paste volume needs separate consideration.
  • If the connector has locating pegs or press-fit tails, those positions should have no aperture at all — the single most common error when apertures are auto-derived from a pad layer.

Takeaway: on one stencil, chip parts subtract, QFNs subdivide, BGAs stay conservative, and paste-in-hole adds. No global scale factor satisfies all four. "Shrink the pad layer by N%" will fail on at least one family of any mixed-technology board.

6. Shape, area, thickness: which one moves first

When print results disappoint, there are three knobs: aperture shape, aperture area, foil thickness. Their scopes differ enormously, and the wrong order enlarges the problem.

Shape is local. Changing one footprint's aperture shape affects that footprint only. Cheapest, so try it first.

Area is local too, and it maps directly onto release tendency. Reducing area suppresses bridging; overshoot it and you have insufficient paste. It usually moves together with shape — for instance a square aperture becoming a rounded square and pulling in slightly at the same time.

Thickness is global. It changes deposit volume at every aperture on the sheet. Thin the foil for one QFN and every large pad on the board loses paste. So thickness is a global decision to be fixed before the stencil is released, not a debugging lever. If two component families genuinely need different thicknesses on one sheet, that is the signal for a step stencil.

There is also a knob that is not on the stencil at all: the print process window. Squeegee pressure, speed and separation speed all move the result, and adjusting them does not require a new stencil. We covered that line separately. The practical sequence: verify the process window is sane, then change shape, then area, and only then consider recutting. Jumping straight to a recut is the most expensive step and the one most often wasted.

7. What the stencil cannot fix — and the pad design has to

One class of problem can only be mitigated stencil-side, never solved there. Recognising them saves build cycles.

  • The gap between two pads is simply too small. Apertures can shrink, but past a point that becomes insufficient paste. The root cause is pad spacing; fix it on the PCB.
  • Severe thermal asymmetry across one component. One end on a plane, the other on a thin trace. Tombstoning originates in copper distribution; the stencil can equalise paste volume but not heat.
  • Via in pad, unplugged. Paste escapes through the via to the other side. That is resolved in PCB fabrication — plug it or move the via off the pad — not by aperture geometry.
  • Solder mask opening much larger than the pad. Paste has no boundary to hold it and spreads. Fix on the mask side.
  • The board is not flat. See the BGA section: check support and tooling first.

Once these are separated out, the genuinely stencil-owned share is often smaller than expected. That is why our stencil review looks at pad and mask design together — scope is described on the stencil service page and the manufacturing capability page.

8. What the cut file has to declare

Whether a stencil can go straight to cutting depends on whether the incoming package settles the following. Miss one and the shop either asks, or decides for you by convention — the second being the more dangerous outcome.

  1. Is aperture data a dedicated layer, or is the shop expected to derive it from the pad layer? Responsibility differs completely between the two. If the latter, state the expected treatment. The package-to-cut-file conversion relationship has its own article.
  2. Which pads get no aperture. Locating pegs, press-fit tails, test points, do-not-place references. This is where auto-derivation fails most often.
  3. Which references need special treatment. Whether large thermal pads are subdivided and how; the paste-in-hole reference list.
  4. Whether pad-to-aperture differences are already baked into the data or expected to be applied by the shop. "Process per standard" is not a usable input.
  5. Foil thickness, and whether stepping is permitted. Thickness is a global item and must be explicit.
  6. Frame specification and effective print area. Unrelated to aperture shape, but without it nothing can be cut.
  7. Whether fiducials or auxiliary marks are required, and their position requirements.
  8. Which revision is final — and the matching PCB revision. A stencil-to-board revision mismatch makes correct apertures irrelevant.

Put these in the accompanying notes and stencil review converges in one round. Otherwise clarification takes longer than the cutting.

9. Ordering the trade-offs on a mixed board

When one board carries fine-pitch chip parts, QFNs, BGAs and paste-in-hole connectors, those four demands compete. A workable order:

First, fix thickness. It is global and it is locked by the most demanding family — normally the smallest aperture. Check whether that smallest aperture releases acceptably at the chosen thickness; if not, consider stepping or a different stencil fabrication route.

Second, rank by risk, not by count. A board may have hundreds of chip parts and one BGA. But BGA failure costs far more to detect and rework. Put the engineering effort on the BGA and the QFNs.

Third, treat paste-in-hole separately. Its volume demand usually conflicts with the thickness decision. If extended area cannot close that gap, those through-hole parts may not belong in reflow at all — a process-route question, not an aperture question.

Fourth, leave the remaining delta to the print window. Do not try to absorb every variable in geometry. A stencil that leaves some room for process adjustment has a wider usable range.

Fifth, run a reverse check before release: overlay aperture data on pad data and confirm, family by family, that the difference points the expected way — chip parts in, paste-in-hole out, BGAs slightly under, QFNs subdivided. If every family deviates in the same direction, a global scale factor was applied and the stencil will most likely need to be redone.

10. Summary

Aperture shape looks like drafting. It is really risk allocation across component families. Chip parts carry their risk between adjacent pads, so they shrink. QFNs carry theirs in volume and trapped gas, so they subdivide. BGAs carry theirs in registration margin, so they stay conservative. Paste-in-hole carries its risk in underfill, so it expands. A good stencil is not one with pretty apertures — it is one where every aperture family's deviation direction has a stated reason.

If you want the aperture data reviewed before release, send the package together with the PCB revision; review scope is on the stencil service page. Board-side tolerances and inspection terms sit on the tolerance page and the quality page.

FAQ

Can apertures be exported directly from the pad layer?

As a starting point, yes; as a cut file, no. The pad layer carries none of the "which pads get no aperture", "which get subdivided", "which get extended" information — and those are exactly the highest-cost errors. A reference-level exception list is the minimum addition.

Is there a universal scale factor to apply?

No. On a mixed board the four families need opposite deviations — chip parts in, paste-in-hole out, BGAs slightly under, QFNs subdivided. Any global factor fails on at least one. Global scaling is only marginally usable when the board carries a single component type.

Do large thermal pads always have to be subdivided?

Subdivision is the common practice, to control deposited volume and give volatiles an escape path. Whether and how to subdivide depends on package and thermal requirements, and should be confirmed by the design side rather than decided by the stencil shop.

Can BGA apertures be square?

Not advisable. Round pad with round aperture is more predictable in both release and printed shape; square corners are stress concentrations, and in a position-sensitive BGA field the extra area is consumed directly out of registration margin.

Insufficient paste — change the aperture or the foil thickness?

Verify the print process window and board support first, then adjust aperture shape and area, and consider thickness last. Thickness is global; changing it for a local problem spreads that problem across the board.

What happens if stencil and PCB revisions do not match?

Apertures land off the pads, and that error typically stays invisible until first article. The accompanying notes must name the PCB revision the stencil belongs to; it is a precondition for release.

Need Professional PCB Manufacturing?

Founded in 2009, we provide one-stop PCB solutions from prototype to mass production.