Sunking PCB

Polyimide Flex PCB Manufacturing: Six Steps That Differ From Rigid Boards

Design Guide2026-10-27Sunking Circuits Technical Team
Polyimide Flex PCB Manufacturing: Six Steps That Differ From Rigid Boards

Polyimide (PI) flex PCBs and FR-4 rigid boards share most of their process steps: panel cutting, drilling, hole metallization, imaging, etching, surface finish and electrical test. The difference is not extra steps. It is that the same step has to be controlled differently because the material is different. PI film has no glass reinforcement, it absorbs moisture, and it changes size under heat and tension. Those three properties create six split points in the flex process chain.

Material properties: the root of every split

  • No glass weave: PI film supports itself. It is thin, soft and bendable, but without a rigid skeleton it stretches and wrinkles during etching, lamination and coverlay bonding.
  • Moisture uptake: PI and coverlay adhesive absorb water from the air. When wet material reaches lamination or soldering temperature, the moisture vaporizes and can cause delamination or blistering.
  • Dimensional movement: after etching removes large copper areas, internal stress in the film is released and the pattern shrinks or grows relative to the design. The amount depends on copper distribution and construction.

Split 1: baking before heat steps

Rigid boards rarely need a separate bake before each thermal step. PI flex base material and coverlay are pre-baked per material requirements before lamination and bonding, and finished flex is often baked again before soldering. On the design side, state the shipping package (for example vacuum moisture-barrier packaging) on the fab drawing and say in the assembly documents who owns the pre-solder bake.

Split 2: scaling and registration

Rigid board compensation is mainly about etch line width. Flex also needs overall scaling: the fab scales the phototool or LDI data based on material lot and copper distribution, and adds registration targets to the panel. What the design can do:

  • Keep copper balanced. Avoid a solid plane on one side and sparse traces on the other.
  • Leave panel space for the fab's registration targets and test coupons.
  • Dimension critical features (connector finger pitch, tooling hole spacing) separately on the drawing so the fab can verify scaling.

Split 3: drilling and desmear

Flex is often stack-drilled between entry and backup boards so the film does not tear or burr as the drill exits. PI and its acrylic or epoxy adhesive smear differently from FR-4, so desmear is usually done with plasma rather than chemical desmear alone. After plating, the barrel has to survive flexing as well as conduct, so holes should stay out of dynamic bend areas. Pad anchoring for plated flex holes is covered in flex PCB plated hole pad anchoring.

Split 4: coverlay instead of solder mask

Rigid outer layers use liquid photoimageable solder mask. Flex bend areas usually use PI coverlay with adhesive, laminated under heat and pressure. Openings are punched or laser cut in advance and then registered to the circuit. Coverlay openings are coarser than solder mask openings, so fine dams between pads are often not achievable. Static areas or fine-pitch component areas can use flexible solder mask locally. Material combinations are covered in flex PCB material selection: polyimide, copper, coverlay.

Split 5: stiffeners

Flex needs stiffeners under connectors, component areas and ZIF fingers. Rigid boards have no equivalent step. Common stiffener materials are PI, FR-4 and stainless steel, bonded with pressure-sensitive or thermoset adhesive, either after surface finish or before assembly. Location, thickness, material and bonding side belong on the fab drawing, especially the total thickness at ZIF fingers. Review points are in flex PCB stiffener drawing review.

Split 6: outline

Rigid outlines are mostly routed. Flex outlines are usually steel-rule or hard-tool punched, or laser cut, and tear risk needs its own attention: radius inside corners, avoid square notches at bend-area edges, and add tear-stop copper or relief holes where needed. Punching versus laser is compared in flex PCB outline punching and laser cutting.

Process comparison

StepRigid PCBPolyimide flex PCB
Material and cuttingRigid panel, cut directlyFilm handled to avoid wrinkles, pre-baked before heat steps
Pattern compensationMainly etch line widthPlus overall scaling and registration targets
Drilling and desmearMechanical drill + chemical desmearStack-drilled with backup, plasma desmear common
Outer protectionLiquid solder maskCoverlay lamination, flexible ink locally
StiffenersNonePI / FR-4 / steel stiffener bonding
OutlineRoutedPunched or laser cut, tear control

Adapting the design inputs

  • Specify PI thickness, copper type (rolled annealed or electrodeposited), adhesive system, and adhesive or adhesiveless base.
  • Mark dynamic bend areas and static areas. No holes or components in bend areas.
  • Define coverlay openings and solder mask areas separately.
  • List every stiffener with material, thickness and location.
  • Dimension critical features separately and allow the fab to scale the rest.
  • State shipping packaging and who owns the pre-solder bake.

SKPCB flex PCBs are built in 1–8 layer polyimide constructions with 2 mil minimum trace and bend radius from 6× board thickness. See the flex PCB product page for constructions, rigid-flex PCB when rigid sections are needed, and request a quote once the data package is ready.

Summary

The polyimide flex process chain follows the rigid chain in outline but departs at six points: moisture baking, dimensional scaling, stack drilling with plasma desmear, coverlay lamination, stiffeners, and punched or laser outlines. The cause is that PI has no glass, absorbs moisture and moves. A design package that states the construction, bend areas, opening method, stiffeners and critical dimensions avoids most engineering queries.

FAQ

Q: Why does polyimide flex need baking?

A: PI and adhesive absorb moisture. At lamination or soldering temperature the water vaporizes and can cause delamination or blistering. A pre-bake removes it.

Q: Why do flex dimensions differ from the design?

A: PI has no glass to restrain it, so the film moves when etching releases stress. The fab scales by material lot and copper distribution; the design should balance copper and dimension critical features.

Q: Can flex PCBs use solder mask?

A: Bend areas normally use coverlay. Static or fine-pitch areas can use flexible solder mask locally.

Q: When are stiffeners applied?

A: Depending on stiffener material and assembly flow, after surface finish or before assembly. The drawing should state material, thickness, location and bonding side.

Q: How many layers can SKPCB build in flex?

A: 1–8 layer polyimide constructions, 2 mil minimum trace, bend radius from 6× board thickness.

Prototyping a flex or rigid-flex board?

Bend radius, coverlay and stiffener placement decide reliability. Tell us the bend cycles and assembly method and we will propose a construction with pricing.