1. On flex, the outline is its own engineering decision
On a rigid board the outline rarely consumes design attention: draw a board edge, hand it to a router, accept the standard tolerance class. Flex does not work that way.
The difference is in what is being machined. A rigid board being routed is a panel that holds itself in place; the cutter removes the edge material and the remainder does not move. A flex circuit is a polyimide film composite in the sub-millimetre thickness range — no glass weave skeleton, no rigidity worth speaking of against lateral force. The moment a tool or a die applies lateral force, the material is first pulled and displaced, and only then separates. The gap between where it separated and the line you drew is the dominant source of flex outline tolerance, and it is governed not by machine positioning accuracy but by how the material was constrained at that instant.
This inverts the usual causal order. On rigid boards you fix the outline, then ask about tolerance. On flex, you first decide how it will be cut, and only then know whether that outline is producible and which tolerance class applies. When the outline method is not treated as a design input, a familiar failure appears: stackup, routing and coverlay all clear review, and the outline stage is where someone discovers a cutout cannot be produced — at which point changing the outline usually drags coverlay openings and stiffener positions with it, sending the job back to stackup review.
This article covers only how the outline contour gets cut. Stackup and overall manufacturing limits are in flex PCB construction and manufacturing limits; bend-area routing rules, coverlay material selection and stiffener drawing review each have their own article and are not repeated here.
2. Three outline methods, and one that does not apply
Hard die cutting (steel die blanking). Matched upper and lower dies form the shape in one stroke, with the entire contour separating simultaneously. This is the common method for volume flex: short cycle time per piece and good contour consistency, because every board shares one die, so shape deviation does not accumulate board to board. The cost is the die itself — a physical tool made for that one outline. Change the outline and the die must be modified or remade. Die cutting therefore suits projects whose outline is frozen and whose volume amortises the tooling.
Laser cutting. No physical contact; energy traces the contour in the material. The advantages are direct: no tooling, so an outline revision is only a program change, and features can be produced that a die cannot, because there is no cutting-edge strength or minimum die wall to respect. The cost is that it is a point-by-point, line-by-line process, so cycle time scales with contour length. Cutting is also fundamentally a thermal process — the edge condition at the kerf differs from a mechanical die break, and that should be handled in downstream review as a known difference rather than as a defect.
Steel rule die (soft die / rule cutting). Blades are set into a board to form the cavity and press through the material. This sits between the other two: tooling cost is far below a hard die and lead time is short, which suits samples and lower volumes. But the blade dulls with use, and the rule itself has a minimum bend radius, so the smallest corner radii and narrowest features it can form fall short of both hard die and laser.
Why not routing. The default answer for rigid outlines is a cutter following the contour (see rigid board profiling and V-cut tolerance control), but routing has two hard problems on flex. The cutter's lateral force acts precisely on the material least able to take lateral force, so the film lifts and curls. And routing requires the workpiece to be firmly clamped; clamping flex means first bonding it to a carrier, which turns the question from "how do we cut this" into "how do we hold it down before cutting". In practice flex outlines are produced by die cutting, laser or steel rule die, with routing appearing only in the rigid sections of rigid-flex.
3. What happens to the material at the moment of cutting
Understanding the three methods means looking at the material side, not the equipment side.
A flex circuit is a laminated composite: polyimide base film, adhesive, copper foil, coverlay — each layer with different stiffness and different bond to the adhesive. When a contour passes through those layers, fracture does not occur at the same position in every layer at the same instant. In die cutting the upper layers are pressed in first and the lower layers separate afterwards, so the upper and lower edges of the contour are not in identical condition. Where the contour crosses copper foil, the difference in fracture behaviour between metal and polymer is more pronounced still. This is why a flex outline drawing should state which side the contour is viewed from, rather than giving only a neutral line.
There is a second layer: residual stress. A flex circuit has already been through lamination and thermal processes, so stress exists inside the material. Cutting the outline releases that piece from the panel, the stress redistributes, and a contour measured immediately after cutting can differ from the same contour after it has rested. This is one root reason flex outline tolerance cannot reach the same class as rigid, and why raising cutting-machine accuracy alone does not solve it.
The design implication is concrete: realistic flex contour tolerance bands are wider than rigid, and do not define functional fits on a flex outline. Positions needing accurate mating — assembly location, connector alignment — belong in a rigid section, in a stiffener area, or should be carried by holes. Holes are a separate drilling operation and are not subject to the material displacement of outline cutting (SKPCB standard minimum mechanical hole 0.2 mm).
4. Which design features constrain the outline method
This is the part most often reworked late. The features below are not yes/no questions about feasibility; they are questions of which methods remain available once you draw them.
Cutouts and narrow slots. A notch cut inward tests tool strength directly. A hard die must retain a thin, narrow blade section at that position; the narrower and deeper the notch, the more readily that section deforms or breaks under press load. A steel rule die reaches its limit earlier. Laser has no such constraint, which makes a deep narrow cutout the single feature most likely to lock the outline method to laser.
Connecting necks. The narrow transition joining two wider regions. The narrower the neck, the more readily it is pulled out of shape during cutting, and the more that downstream handling, assembly and folding concentrate stress there. The engineering response is generous corner transitions at both ends of the neck rather than square corners.
Corner radii and sharp corners. Corner radius on a flex contour is not cosmetic. A sharp corner is a stress concentration and a tear initiation site — tearing that starts at an outline corner and propagates through the base film is a classic flex failure mode. Round every external corner, and match the radius to the chosen method: a steel rule die's blade bending capability limits the smallest radius it can form.
Window and stiffener positions relative to the outline. When a coverlay opening edge sits too close to the contour, the material displacement from cutting lands on the opening boundary and can compromise coverlay encapsulation of the copper. The same logic applies to stiffeners: keep stiffener edges offset from the contour, and do not let the outline cut exactly at the stiffness discontinuity between stiffener and flex area, which is where material behaviour is least predictable.
Datums. If outline, holes, circuitry and openings each reference something different, tolerances stack beyond control. The drawing should give one datum system and dimension the outline to it, not to an arbitrary edge or component.
5. Method against feature
| Consideration | Hard die cutting | Laser cutting | Steel rule die |
|---|---|---|---|
| Tooling | Dedicated hard die; outline change needs die rework | None; outline change is a program change | Soft die; cost and lead time below hard die |
| Suited stage | Frozen outline, stable volume | Samples, frequent revisions, complex contours | Samples and lower volumes |
| Deep narrow cutouts | Limited by blade section strength | Not limited by this | Limit appears earlier |
| Minimum corner radius | Better than steel rule | Least constrained | Limited by blade bending capability |
| Contour consistency | Good within a batch on one die | Depends on program and material fixturing | Varies with blade wear |
| Contour length affects cycle time | Insensitive (one stroke) | Sensitive (traced line by line) | Insensitive |
| Edge character | Mechanical fracture | Thermally processed edge | Mechanical fracture |
No figures are given in the table, because achievable minimum features depend on the material combination, total thickness, copper distribution and contour geometry of that specific build and must be confirmed case by case. Submit the stackup together with the outline drawing when specific values are needed.
6. The boundary with rigid-flex
On rigid-flex (SKPCB engineering-confirmed up to 20 layers) the outline question splits in two: rigid sections can be routed like rigid boards, while flex sections still need die cutting or laser. The junction between them — the rigid-to-flex transition zone — is the worst place on the board for a contour to pass through, because stiffness changes over a very short distance and the two sides respond completely differently to cutting. Designs should route the outline clear of the transition zone, or contain the zone entirely within the board. Structural selection differences are covered in rigid-flex vs flex PCB construction boundaries.
7. What to supply with the order
Missing outline information is a common reason flex projects stop at engineering review. Include:
- Outline drawing with one datum system, contour dimensioned to that datum, stating the viewing side.
- Whether the outline may still change. If it is frozen and volume is stable, say so and die tooling can be prepared; if revisions are expected, laser saves time first.
- Where the minimum features are. Call out the narrowest neck, the deepest cutout and the smallest radius explicitly instead of making engineering hunt for them.
- Relative positions of openings, stiffeners and the contour, especially the tightest clearances.
- Where functional fits land, so it can be judged whether holes or a rigid section should carry them instead.
- Panelisation and connection intent, since flex panel connection positions affect both outline cutting and later depanelisation.
SKPCB flex and rigid-flex capability is at flex PCB and rigid-flex PCB; tolerance class definitions are at tolerance capability. Acceptance runs to IPC-6012 Class II and Class III, with flex additionally reviewed against the IPC-6013 framework; all orders receive 100% electrical test and the process carries 10+ inspection gates — see quality system.
FAQ
Q1: Can a flex outline be routed like a rigid board?
Generally not advisable. The cutter's lateral force on a film with no rigidity causes curling and displacement, and the board must be bonded to a carrier before machining is even possible. Flex outlines are produced mainly by hard die cutting, laser cutting and steel rule die; routing is normally reserved for the rigid sections of rigid-flex.
Q2: Which method should the sample stage use?
Choose laser while the outline may still change, because a revision is only a program change and creates no tooling rework. Reassess die cutting once the outline is frozen and volume has started, trading tooling for cycle time and within-batch consistency. A steel rule die suits the middle case: largely settled shape, modest quantity.
Q3: Why can't flex contour tolerance match rigid?
Two effects compound: material is pulled and displaced at the instant of cutting, and residual stress redistributes once the outline is released, changing the contour. Both are material behaviour, so machine accuracy cannot remove them. Submit the stackup for engineering confirmation of the achievable class.
Q4: Do sharp outline corners really have to be rounded?
Round all of them. A sharp corner is a stress concentration and the classic initiation site for tearing from a flex outline. Match the radius to the chosen method as well — a steel rule die's blade bending capability limits the smallest radius it can form.
Q5: What happens if the contour runs too close to a coverlay opening or stiffener edge?
Material displacement during cutting can land on the opening boundary and compromise coverlay encapsulation of the copper. If the contour cuts exactly at the stiffness discontinuity between stiffener and flex area, material response is least predictable. Offset the contour from these boundaries and mark the tightest clearances on the drawing for review.
Q6: How should positions requiring accurate fit be handled?
Not on a flex-area contour. Carry them on holes instead — holes are a separate drilling operation unaffected by outline cutting displacement, SKPCB standard minimum mechanical hole 0.2 mm — or place them in a rigid section or stiffener area.

