Edge plating (also called edge metallization, side plating or castellated edge wrapping) puts a continuous copper layer on one or more sections of the board outline and connects it to the ground planes inside the board. It is common on RF modules, high-speed boards and boards that sit inside a metal cavity.
It sounds like "plate the edge with copper", but it only works when routing, plating and final profiling run in a specific order. Get the order wrong and there is no edge copper to keep.
1. What edge plating is for
- Shielding: copper on the sidewall closes the dielectric edge so RF energy and high-speed noise do not leak out sideways.
- Grounding: when the board is mounted in a metal housing or cavity, the plated edge gives a large contact area to the enclosure.
- Heat transfer: the edge copper adds a thermal path toward the chassis.
- Edge contact: some module boards use the plated edge as a solder or press contact surface.
2. Edge plating vs castellated holes vs via fences
| Method | Structure | Typical use |
|---|---|---|
| Edge plating | Continuous copper on the outline sidewall | Shielding, grounding, cavity mounting |
| Castellated holes | Plated holes cut in half along the edge | Soldering a module onto a carrier board |
| Via fence | Row of ground vias inside the outline | Shielding, but the dielectric edge stays bare |
A via fence still leaves dielectric gaps between holes. Edge plating closes that section of sidewall completely. The two are often combined. Design points for half holes are covered in our castellated holes guide.
3. Process sequence: why the edge is milled first
On a standard PCB the outline is routed after the surface finish, so the sidewall only shows laminate and copper cross-sections. For edge plating the sidewall has to exist before plating, so the flow changes:
- Pre-mill edge slots after drilling: a through slot is routed along each edge section to be plated. This exposes the sidewall and the cross-sections of the inner ground planes. Tabs between the slots keep each board held in the panel.
- Electroless copper and electroplating: the slot walls go through desmear and electroless copper like any drilled hole, then are electroplated. Sidewall copper fuses with the exposed plane edges.
- Outer-layer imaging and etching: the edge copper is tied to surface copper according to the pattern.
- Solder mask and surface finish: edge copper normally receives the same finish as the board surface to prevent oxidation.
- Final profile: the tabs are routed off and the board leaves the panel. There is no edge copper where the tabs were.
A finished plated edge is therefore usually a set of continuous copper sections separated by tab locations. A full perimeter with no break needs a special panel-holding method and should be confirmed with the fabricator at quotation.
4. What the design data must state
Edge plating cannot be inferred from the outline layer in the Gerber set. It needs explicit instructions:
- Plated edge sections: mark on a mechanical layer or the fabrication drawing which edges are plated and where each section starts and ends, using a dedicated line style.
- Connection to planes: specify which inner and outer planes extend to the edge. Sidewall copper only bonds to copper that reaches the outline; a pulled-back plane will not connect.
- Copper pullback on non-plated edges: all other edges keep the normal copper-to-edge clearance so routing does not expose or lift copper.
- Tab locations: state where tabs are allowed or forbidden. Edges where breaks are not acceptable need an agreed panel method.
- Components and keep-outs near the edge: the plated edge touches the housing or shield can, so pads and traces near it must respect the assembly clearance.
- Surface finish: say whether the edge copper takes the same finish as the board surface.
Actual pullback distances and slot widths depend on board thickness, layer count and equipment, and are set during the engineering DFM review once the data is submitted.
5. Common defects and causes
- Lifted or peeling edge copper: weak bond from incomplete desmear or electroless copper on the slot wall, or the router pulling on the copper during final profiling.
- Burrs and copper slivers: the cutter clips the copper during profiling and leaves burrs that can short.
- Bare laminate spots on the sidewall: incomplete plating coverage in the slot or later handling damage.
- No connection to the ground plane: the inner plane was pulled back at the edge, or layer misregistration left the cross-section only partly exposed.
- Breaks at tab locations: an inherent result of the design; accept them on the drawing up front or agree on a different holding method.
6. How plated edges are inspected before shipment
- Visual and magnified inspection: check edge copper continuity, lifting, burrs and exposed laminate.
- Microsection: section a sample through the edge to confirm sidewall coverage and connection to the inner planes, judged against the ordered IPC-6012 class.
- Electrical test and ground continuity: SKPCB runs 100% electrical test on all orders. When the netlist includes the ground net the edge connects to, a broken edge-to-plane connection shows up.
- Recheck after thermal stress: for high-reliability builds, inspect the edge bond after thermal stress as agreed in the order.
SKPCB runs reliability testing on every lot and accepts work to IPC-6012 Class II and Class III. Edge plating is a structure reviewed case by case, so send the fabrication drawing with the plated sections marked and request a free DFM review at quotation.
FAQ
Q: Is edge plating better for shielding than a via fence?
A: Edge plating closes the dielectric sidewall completely, while a via fence leaves gaps between holes. Whether you need edge plating depends on frequency and shielding targets; many designs use both.
Q: Can the whole perimeter be plated with no breaks?
A: Standard processing leaves breaks at the tab locations. A continuous perimeter needs a special panel-holding method that should be confirmed before quotation.
Q: Does the plated edge need a surface finish?
A: Yes. Bare copper oxidizes and degrades ground contact and appearance, so the edge usually takes the same finish as the board surface.
Q: Which process steps does edge plating add?
A: Mainly the pre-plating edge slot milling and a modified final profiling step. These changes affect cost and lead time, which are confirmed in the quotation.

