Most flex circuits have simple routing. The trouble usually sits at the end: the tail will not go into the connector, makes intermittent contact, lifts a pad after hot-bar soldering, or misaligns during ACF bonding. These are rarely routing errors. Most come from choosing a connection method without writing its manufacturing inputs onto the drawing.
The connection method should be fixed during layout. It decides the total thickness at the tail, whether a stiffener is needed, which surface finish to use, where the coverlay opens and whether fiducials are required. The table below compares the four common methods; each is explained afterwards.
Four methods compared
| Method | Flex tail | Key manufacturing inputs | Detachable |
|---|---|---|---|
| ZIF/LIF insertion | Exposed contact fingers | Total thickness at contacts, stiffener, hard surface, outline tolerance | Yes |
| Board-to-board connector | Connector soldered onto the flex | Stiffener under the connector, flatness, pad finish | Yes |
| Hot-bar soldering | Exposed pads soldered to main-board pads | Coverlay opening, pre-tinning, heat resistance, fiducials | No |
| ACF bonding | Fine-pitch flat pads | Pad flatness and finish, fiducials, no mask over pads | No |
A fifth option is to avoid the joint. A rigid-flex board moves the connection into one stackup and removes the tail interface, at the cost of a more complex build.
ZIF/LIF insertion: the connector sets the thickness
A ZIF connector clamps the fingers against its contacts and accepts only the total thickness range in its datasheet. Too thin gives low contact force; too thick will not insert or damages the contacts.
The flex itself is usually thinner, and a stiffener on the back of the contact area makes up the difference. The drawing should state:
- target total thickness and tolerance at the contacts, citing the connector datasheet;
- stiffener material (PI is common), stiffener thickness and adhesive, all counted in the total;
- finger finish: electroplated hard gold for frequent mating, ENIG for few cycles, following the connector maker's advice;
- finger width, pitch, length and the distance from the outline edge to the first finger, since outline tolerance drives alignment;
- coverlay opening position relative to the finger roots, so the coverlay edge stays out of the contact zone.
How to draw the stiffener itself is covered in our stiffener drawing review.
Board-to-board connectors: stiffener and flatness
When a connector is soldered onto the flex, the mounting area must become rigid first. Placed directly on flexible material, the joints see bending stress during reflow and mating and can crack.
Inputs to provide: stiffener area under the connector (FR-4 or metal, bonded on the back), flatness of the stiffened pad area, pad finish (ENIG is common), the transition zone around the connector and the distance between the bend area and the connector. SKPCB's flex specification calls for a bend radius of at least 6× board thickness; keep the bend line off the stiffener edge.
Hot-bar soldering: pads, solder and heat
Hot-bar soldering uses a heated thermode to solder the flex pads directly to main-board pads. It needs no connector and has the smallest footprint and cost, but it cannot be undone.
Flex-side inputs: coverlay opening over the pad area with room for the thermode; whether pads are pre-tinned and which finish they carry; the transition from pad root to coverlay edge, so pads do not peel at the root under pressure; at least two fiducials. The joint is heated locally, so the PI base and adhesive must survive the process temperature; confirm time and temperature with the soldering process. Pad anchoring is covered in our flex pad anchoring article.
ACF: fine pitch and flatness
ACF (anisotropic conductive film) conducts through particles in the bonding direction only. It handles pitches hot-bar cannot and is common for display modules and sensors.
Its demands on the flex are all at the pads: a flat pad area free of mask and coverlay, an even finish (ENIG is common), pad width and pitch designed to the ACF material and bonder requirements, and clear fiducials. SKPCB flex supports a 2 mil minimum trace width, but whether a given fine-pitch pad pattern is buildable should be confirmed with the factory against the actual design.
Where missing inputs show up
| Missing input | Where it fails |
|---|---|
| Total thickness at contacts | Final assembly: will not insert or poor contact |
| Stiffener area and adhesive | Joints crack after connector assembly |
| Surface finish not specified | Wear on mating or poor solderability |
| Coverlay opening boundary | Contacts covered or pads peel at the root |
| Fiducials | Misalignment in hot-bar or ACF |
What to send SKPCB
With the RFQ, include: connection method and connector part number or datasheet, target total thickness at the contacts, stiffener material and area, surface finish, coverlay opening drawing and bend area location. SKPCB builds flex in 1–8 layers on PI; if the joint and flex section should be one part, a rigid-flex build can be evaluated. Files can be submitted on the quote page.
Summary
The connection method at the flex tail sets five inputs: thickness, stiffener, finish, openings and alignment. Choose the method first and put its inputs on the drawing, and most tail problems are removed before fabrication.
FAQ
Q: How is the thickness at ZIF contacts determined?
A: By the total thickness range in the chosen connector's datasheet. Flex, stiffener and adhesive together must fall inside it.
Q: ENIG or hard gold for contact fingers?
A: It depends on mating cycles and the connector maker's advice. Use electroplated hard gold for frequent mating and ENIG when the tail is rarely reinserted.
Q: Why does a board-to-board connector need a stiffener?
A: Without one, the joints see bending stress during reflow and mating and can crack. The stiffener keeps the mounting area rigid and flat.
Q: Hot-bar or ACF?
A: Hot-bar suits wider pad pitch and low cost; ACF suits finer pitch where hot-bar cannot keep joints separate. Neither is detachable.
Q: When should I switch to rigid-flex?
A: When there are many joints, little space or high reliability demands, moving the connection into a rigid-flex stackup removes the tail interface.

