Sunking PCB

Drilling and Through-Hole Plating on Heavy Copper PCBs: Why the Standard FR-4 Hole Table Stops Applying

Design Guide2026-10-09Sunking Circuits Technical Team
Drilling and Through-Hole Plating on Heavy Copper PCBs: Why the Standard FR-4 Hole Table Stops Applying

When engineers quote a heavy copper board, the most common move is to take the standard FR-4 capability table, copy over the hole sizes, aspect ratio and registration figures, and change one field: copper weight to 6 oz or 12 oz. The files go out, and engineering review comes back with a list of hole-related questions.

The reason is not that the shop lacks capability. It is that the process conditions the table describes no longer hold. On a standard board the hole wall is almost entirely resin; copper occupies two very thin rings at the top and bottom. The drill is cutting glass cloth and resin, and the copper is effectively negligible. Past roughly 6 oz, this inverts: the hole wall now carries metal rings hundreds of microns thick, and inside a single hole the drill alternates between two materials whose removal behaviour is opposite. Resin is brittle, softens with heat, and gets carried out of the hole. Copper is tough and ductile — it gets pushed rather than cut.

That is the entire source of difficulty in heavy copper drilling. It is not "the same process, somewhat harder." The set of binding constraints has changed.

This article covers one process chain only: drilling and through-hole metallisation on heavy copper. How copper weight changes hole geometry, how thick inner layers affect layer-to-layer registration after lamination, how hole size and aspect ratio need re-constraining, and what to inspect at acceptance. General heavy copper manufacturing limits and DFM (trace width and spacing, etch compensation, solder mask coverage, stackup design) are out of scope.

A note on where this sits relative to two product pages, so you do not land on the wrong entry point: the heavy copper PCB page is the capability and application entry — how thick we can go and what it is used for. The thick copper PCB page addresses specialty requirements at higher copper weight tiers. This article does not repeat the capability figures on either page. It answers one engineering question: how the process constraints on holes change under heavy copper — the product pages tell you what can be built, this tells you why the holes are the ceiling you hit first.

---

1. Copper and resin: two removal behaviours in one hole

Thinking of drilling as "removing material" is what leads people astray on heavy copper. The drill encounters two classes of material stacked in alternation, and they fail in nearly opposite ways.

Resin and glass cloth soften under heat. Friction from the drill generates heat, and softened resin is pushed and smeared onto the hole wall that has already been formed — this is smear. Glass fibre, by contrast, is hard and brittle; cutting it wears the drill edge. On a standard board those two effects are essentially the whole story of hole-wall quality: smear and protruding fibre.

Copper does not soften under heat; it becomes more ductile. When the drill edge reaches a thick copper layer and cutting conditions tip toward pushing rather than shearing, the copper does not fracture and release. It gets displaced along the hole axis. Displaced toward the exit side it forms a burr; displaced into the hole wall it leaves a rolled lip or a smeared metal layer.

In a heavy copper hole, both behaviours alternate repeatedly within a single feed: copper, resin, copper, resin. Each boundary is an abrupt change in cutting condition. The positions most likely to go wrong on the hole wall are the copper-to-resin interfaces, not the middle of the hole.

This is why hole-wall inspection priorities differ from standard boards. Standard boards look at smear coverage and fibre protrusion. Heavy copper boards additionally require looking at hole-wall continuity at the copper interfaces — whether displaced copper has created a step, a void, or folded-in metal. Those defects become discontinuities in the plating that follows.

---

2. Burrs: why they become a standalone problem on heavy copper

Standard boards get burrs too, but burr height is bounded by the foil thickness itself. There is only so much copper available to displace, and routine deburring handles it.

As copper weight increases, the volume of metal available for displacement scales with it. The burr at the hole mouth is no longer a thin curled rim but a metal ring of real thickness. That creates three downstream problems.

First, it interferes with contact in later process steps. Raised metal at the hole mouth means the panel surface is not flat there. Dry film lamination, solder mask printing and stacking for lamination all suffer local contact defects at that point.

Second, removing it can take hole-mouth copper with it. Deburring acts mechanically or chemically at the hole mouth. Strong enough to remove a thick burr means strong enough to act on the surrounding copper surface, leaving hole-mouth copper thickness inconsistent with the panel surface.

Third, it can change the hole diameter at the mouth. When a burr curls inward, the effective opening at the mouth is smaller than the drilled diameter. Measure against hole size tolerance and you get different readings at the mouth and mid-hole.

SKPCB's hole size tolerances are PTH ±0.075 mm, NPTH ±0.05 mm, and press-fit ±0.05 mm. These still apply on heavy copper, with one caveat: they apply to the finished hole after cleaning and deburring. If your inspection flow takes readings before deburring, or only at the hole mouth, the deviation you measure does not represent the finished part. Press-fit holes are especially sensitive — a press-fit connection relies on interference between hole wall and terminal, so residual burr or a narrowed mouth directly changes insertion force.

So in a heavy copper hole specification, deburring has to be treated as a process step with acceptance requirements, not covered by the phrase "standard processing."

---

3. How thick inner-layer copper changes layer-to-layer registration

This section is specific to heavy copper multilayers; it barely exists on standard boards.

Registration is fundamentally geometric: the drill has to pass through connection pads pre-etched on each inner layer. Drill off-target and you hit the pad edge or break the connection entirely. Controlling registration presupposes knowing where each inner layer actually sits after lamination.

On standard boards, inner-layer copper is thin enough that resin flow during lamination is essentially uniform, and X/Y shrinkage can be predicted with empirical compensation factors. Thick inner-layer copper breaks that premise in three ways.

Resin flow and fill change. Thick inner-layer copper has significant topography, and during lamination resin has to fill the gaps between thick copper features. The volume required varies across the panel — large copper areas need almost no fill, while fine-feature regions need substantial resin flow. Different flow volume means different local shrinkage.

Copper-covered regions resist shrinkage; bare regions do not. Copper's thermal expansion behaviour differs from resin's. Regions with high thick-copper coverage are pinned by the copper as the panel cools; cut-outs and bare areas shrink more. Panel dimensional change is therefore no longer uniform scaling but non-uniform distortion correlated with copper distribution.

Mixed copper weight stackups compound this. When a board carries both heavy and standard inner-layer copper, each layer shrinks differently, and registration has to satisfy all of them simultaneously.

The manufacturing answer is to compensate from measured post-lamination layer positions before drilling, rather than from fixed shrinkage coefficients. SKPCB's hole position accuracy is ±0.05 mm (normal conditions). This number describes the equipment and process capability for hole position — it does not mean your connection pad cannot be missed. Whether a pad is hit depends jointly on hole position accuracy and on the uncertainty in where the inner layer actually sits. Heavy copper stackups increase the latter.

The practical implication for design is one sentence: do not specify inner-layer annular ring at the standard-board minimum on a heavy copper multilayer. Annular ring is the margin that absorbs registration uncertainty, and heavy copper enlarges that uncertainty. Specify it too tight and engineering review will ask for larger pads; changing it back costs more time than allowing margin up front. Layer count and thickness boundaries are on the multilayer PCB page; tolerance definitions are on the tolerance page.

SKPCB's layer capability is 40 layers in standard production, up to 64 layers, with board thickness 0.2–6.0 mm (6.0 mm maximum). Heavy copper stackups approach the thickness ceiling faster than standard boards — at the same layer count, a heavy copper board is thicker. That feeds directly into the next section.

---

4. Hole size and aspect ratio: why heavy copper hits the ceiling earlier

Aspect ratio is board thickness divided by hole diameter. SKPCB's maximum is 10:1 for PTH. It is a process constraint: the deeper and narrower the hole, the harder it is for plating solution to exchange inside it, and the harder it becomes to make mid-hole plating match the hole mouth.

Heavy copper pushes toward that limit from both directions.

Thickness side: as described above, a heavy copper board at a given layer count is thicker. Copper consumes thickness budget, and enough resin is still needed to encapsulate thick copper features. The numerator grows.

Hole size side: heavy copper boards serve high-current paths, and the design instinct for a high-current hole is "make it large," which helps aspect ratio. But the same heavy copper board usually also carries control and signal sections, where holes are sized by signal-board habit. What actually hits the ceiling is usually the smallest signal hole on a heavy copper board, not the high-current holes.

So review a heavy copper hole table this way: not by average hole size, but by computing aspect ratio from the smallest hole on the board against the full board thickness. That combination is the one most likely to exceed the limit, and in the design files those two fields are often filled in by two different people.

Mechanical drilling minimum is 0.2 mm (standard) / 0.15 mm (best capability); laser is 0.1 mm (standard) / 0.075 mm (best capability). Note carefully: laser drilling is a blind-via process and does not solve through-hole requirements on heavy copper. Through-holes on heavy copper can only be mechanically drilled, so the real floor on minimum hole size is the mechanical figure. Entering laser values into a heavy copper through-hole requirement field is a fairly common error in these files.

One further constraint under heavy copper: the smaller the hole, the higher the proportion of the hole wall made of thick copper, and the more concentrated the interface problems from section 1 become. Small holes with heavy copper is the narrowest process window on the board. If design allows, enlarging hole size one step in heavy copper regions pays off more than pushing the hole size limit.

---

5. Through-hole plating: the plating has to cross a copper-resin interface

The goal of through-hole metallisation is a continuous copper layer on the hole wall that reliably connects to every inner layer. Two things are specific to heavy copper.

The substrate is non-uniform. Plating has to grow on alternating copper and resin surfaces. Copper is metal — activation and initiation are easy. Resin has to be chemically treated to become conductive first. The two surfaces initiate differently, so the interface is where plating thickness steps or adhesion shortfalls are most likely. This is exactly why hole-wall geometry at the interface has to be controlled back at the drilling stage — a step or rolled copper lip left by drilling becomes a thin spot in the plating here.

Desmear is harder to calibrate on heavy copper. Desmear removes smeared resin from the hole wall so that the inner-layer copper cross-section is cleanly exposed and plating can connect to it. Too weak, and resin remains at the inner-layer connection, producing a poor connection. Too aggressive, and resin is over-removed, leaving hole-wall recesses or protruding glass fibre. Heavy copper has a large inner-layer copper cross-section requiring more exposure, while the adjacent resin regions remain conventional. The window is squeezed from both sides.

On plated copper thickness, one thing must be explicit: this article gives no micron figure for hole copper. SKPCB's capability register contains no hole-copper thickness entry, and supplying a number would be fabrication. Hole copper requirements should be specified in the order against your chosen IPC-6012 class — SKPCB's acceptance classes are IPC-6012 Class II and Class III, and the classes impose different hole copper requirements. State the class in the files, not "per standard."

Likewise, drill speed, feed rate, bit life, desmear dwell and bath parameters are internal manufacturing controls, outside any external commitment, and no figures are given here. What you need to constrain is the outcome — hole-wall integrity, inner-layer connection, hole copper class, hole size and position tolerance — not the process parameters.

---

6. Acceptance: what to watch on heavy copper holes

Microsection of the hole wall and inner-layer connections. This is the only direct way to judge whether through-hole metallisation succeeded. On heavy copper, deliberately examine the copper-to-resin interface positions, not just mid-hole. Look for plating continuity, residual resin at inner-layer connections, thin spots or voids at the interfaces, and hole-wall recesses from over-aggressive desmear.

Hole-mouth geometry and deburring result. Confirm burrs are removed, hole-mouth copper has not been excessively thinned, and the mouth diameter has not narrowed from an inward-curled burr. Press-fit holes must be confirmed separately.

Measured hole size and position. Take diameter readings at both the mouth and mid-hole. On heavy copper multilayers, judge hole position against the actual inner-layer pad positions, not just absolute coordinates.

Electrical continuity. SKPCB performs 100% electrical test on all orders (flying probe or fixture). Electrical test finds opens and shorts, but be clear about its boundary: passing electrical test does not mean hole copper thickness meets the class, nor that hole-wall geometry is acceptable. A hole with thin but continuous plating passes cleanly and may still fail under thermal cycling. Hole quality is judged by microsection and geometry; electrical test is a backstop. The quality system overall is described on the quality page.

Thermal-stress verification must be stated in the order. Heavy copper boards mostly serve high-current and heat-generating applications, where holes endure repeated thermal cycles. If your application needs evidence of hole-wall integrity after thermal stress or thermal cycling, agree it at order stage against the applicable standard method (the relevant IPC-TM-650 method) and specify sampling and criteria. This is not a default; adding it afterwards means rebuilding the panel.

---

7. How to fill in these fields when you order

Folding the above into checkable line items:

  1. Give copper weight per layer, not a single "copper weight" field. Outer and inner layers, and different inner layers, each need their own figure. Mixed-weight stackups require the full layer order with each layer's copper weight.
  2. Compute aspect ratio from minimum hole size and board thickness together and check it against 10:1 yourself. If it exceeds, either enlarge the hole or reduce thickness — decide before ordering rather than leaving it to engineering review.
  3. Distinguish through-holes from blind and buried vias, and do not enter laser minimum hole size into a through-hole requirement.
  4. List press-fit holes separately, note the terminal type or hole size requirement, and state acceptance against press-fit tolerance (±0.05 mm).
  5. State hole copper requirements as an IPC-6012 class (Class II or Class III) — not "per standard" or "normal."
  6. Give inner-layer annular ring as a design value plus an acceptable minimum. Registration uncertainty is larger on heavy copper stackups; margin up front beats enlarging pads later.
  7. Put deburring and hole-wall acceptance requirements in the files rather than leaving them to the shop's own judgement.
  8. If you need thermal stress or thermal cycling evidence, state it at order stage with the standard method and criteria.
  9. Sampling requirements for test and microsection: whether a microsection report is needed, how many samples and from where.

Prototype lead times are tiered by layer count: 24 h for 2 layers, 48 h for 4, 72 h for 6–8, 96 h for 10–12 (expedited basis). Heavy copper boards typically take one more round of engineering review than standard boards; filling in the fields above completely is what removes that round. Capability overview and submission entry: capabilities.

---

FAQ

Q1: Do heavy copper boards always need larger holes?

Not "always," but enlarging one step is usually worth it. The smaller the hole, the higher the proportion of thick copper on the hole wall, the more concentrated the copper-resin interface problems, and the tighter the aspect ratio. Absent a design reason requiring small holes, going one step up in heavy copper regions relieves both constraints. Note that what hits the ceiling is usually the smallest signal hole, not the high-current holes.

Q2: Can I apply my standard FR-4 hole table directly to heavy copper?

The figures themselves still apply — hole size tolerance (PTH ±0.075 mm, NPTH ±0.05 mm, press-fit ±0.05 mm), hole position accuracy (±0.05 mm normal), maximum aspect ratio (10:1). What does not transfer are the implicit assumptions behind standard-board experience: that annular ring can sit at the minimum, that deburring is covered by default handling, and that a given layer count implies a given thickness. All three need recalculating on heavy copper.

Q3: How thick should hole copper be on a heavy copper board?

Specify it against your chosen IPC-6012 class and state Class II or Class III in the files. This article gives no micron figure — SKPCB's capability register has no hole copper thickness entry, so any specific number requires engineering confirmation against your stackup.

Q4: Why do heavy copper multilayers always get asked for larger inner-layer pads?

Because thick inner-layer copper changes post-lamination shrinkage behaviour. Copper-covered regions shrink less, bare regions more, so panel distortion stops being uniform scaling and the uncertainty in each inner layer's actual position grows. Annular ring is the margin that absorbs that uncertainty. Hole position accuracy itself has not changed; what changed is how precisely the target's location is known.

Q5: If 100% electrical test passes, are the holes fine?

No. Electrical test confirms continuity — opens and shorts. A hole with thin but continuous plating, or one with a hole-wall recess that still conducts, passes. Hole quality is judged by microsection of hole-wall geometry and inner-layer connections. SKPCB runs 100% electrical test on all orders, but its role is a backstop, not proof of hole quality.

Q6: Can laser drilling be used for through-holes on heavy copper?

No. Laser drilling is a blind-via process for interlayer interconnect, not for penetrating the full board. Heavy copper through-holes can only be mechanically drilled, so the floor on minimum through-hole size is the mechanical figure — 0.2 mm standard / 0.15 mm best capability — not the laser 0.1 mm / 0.075 mm. Entering laser values into a through-hole requirement field is a common error.

---

Need Professional PCB Manufacturing?

Founded in 2009, we provide one-stop PCB solutions from prototype to mass production.